ASTM D3451-06 PDF

ASTM D(). Standard Guide for Testing Coating Powders and Powder Coatings. standard by ASTM International, 06/01/ View all product . Purchase your copy of ASTM D – 06() as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards. Mitsubishi GT06 Autotitrator. P-E Headspace .. Coating. Provider. From ASTM. D 5 Samples from powder coating lot to be used. 5.

Author: Shakamuro Mezimi
Country: Barbados
Language: English (Spanish)
Genre: Marketing
Published (Last): 16 August 2008
Pages: 91
PDF File Size: 18.18 Mb
ePub File Size: 9.96 Mb
ISBN: 565-4-79561-565-5
Downloads: 46103
Price: Free* [*Free Regsitration Required]
Uploader: Zolocage

Where more than one test method is listed for the same characteristic, no attempt is made to indicate superiority of one method over another. These properties may be evaluated following the test methods listed in Subscription pricing is determined by: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

We have no amendments or corrections for this standard. Information on current test procedures for pipe and reinforced steel bar coating powders and powder coatings can be obtained through their respective ASTM Subcommittees, A Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Place the pointer between ast two divisions. For example, the appliance industry has developed accelerated tests to simulate the long term service exposure of range stove components to heat cycles or food soils, or both. NOTE 2—The recommended sample size of 0. The physical stability of a thermoplastic coating powder can also be predicted. For the reported hiding power to be signi?

Interpretation of the test results will depend on the speci? Both thermoset and e3451-06 Rather than discover these problems on the production coating line, it is recommended that the compatibility of powders be checked prior to their use. The print test can determine the degree of marring due to pressure.

  ANTIPSICOTICOS TIPICOS Y ATIPICOS PDF

Observe the sharp division between solid and liquid.

In either case, it is important that the viewing and measurement conditions under which the color is to be evaluated are agreed upon between the purchaser and seller.

Abrasion resistance Air blast abrasion tester Falling sand method Taber abraser Adhesion Tape adhesion Chemical resistance Household chemical resistance Detergent resistance Acid resistance Stains or reagents on wood substrates Chip resistance Gravelmeter Edge coverage Electrical insulation Elongation?

For test to test repeatability, it is recommended that the same oven be used for all cured weight loss testing. This standard is not included in any packages. A good correlation between this type of instrument and visual evaluation has been reported.

This standard is ast, available to be included in Standards Subscriptions. Color pigmented coatings Visual Instrumental Do not use abrasives to clean the bar. There is f3451-06 consistent correlation between the two tests.

ASTM D – 06() – Standard Guide for Testing Coating Powders and Powder Coatings

Start Webshop Product catalog Product presentation. The test methods included are listed in Table 1. The benefits of a subscription: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Already Subscribed to x3451-06 document. Guide G provides information on sources of variability in weathering tests, and suggests procedures d4351-06 can be used to cope with this variability.

Historical Version s – view previous versions of standard. Remove the powder quickly and thoroughly before the setting occurs.

These short wavelengths can cause unrealistic degradation when compared to natural exposures. In either case, it is important that the viewing and measurement conditions under which color difference is to be evaluated are agreed upon between the purchaser and seller see Read more about subscriptions.

ASTM D3451 – 06(2017)

Selection of the methods to be followed must be governed by experience and the requirements in each d451-06 case, together with agreement between the purchaser and the seller. The exact identity of the astk lost during the cure cycle would have to be determined by other means to identify what weight percent is organic and inorganic that is, water—see Note 1.

  ECLIPSE BY STEVEN HOLZNER PDF

D Also, it is recommended that comparisons in arti? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

For a very smooth cured? A deviation from the standard bake must be agreed upon between the purchaser and seller. Usage of paint systems is so varied that no one set of conditions length or place of exposure can be given in this guide to cover all situations.

The results are highly dependent on such factors as; the pencil type used, the pressure exerted by the operator, and the care taken in preparing the pencil lead.

ASTM D – Standard Guide for Testing Coating Powders and Powder Coatings

This test is 7 A second method uses a portable instrument that when scanned across the surface acts like the human eye and detects differences in re? You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. The rate and type of degradation produced in exposure to enclosed carbon-arc can be much different from that produced in exposure to the outdoor environment or other types of laboratory light sources.

The cured weight loss may be requested in order to properly determine the exhaust requirements of a bake oven or to comply with state or federal reporting guidelines.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.