REF: BB_SRM_xM BeagleBoard-xM System Revision C Reference Manual BeagleBoard-xM Rev C System Reference Manual Revision April 4, BeagleBoard-xM Rev C/C1/C2 Image BeagleBoard-xM is based on the TI DM and delivers increased performance over the BeagleBoard and is based on an ARM . Bill of Materials · System Reference Manual. 1 Welcome to the Support Page. BeagleBone Black; BeagleBone; BeagleBoard-xM; BeagleBoard.

Author: Dakasa Nanos
Country: Bolivia
Language: English (Spanish)
Genre: Relationship
Published (Last): 17 March 2018
Pages: 350
PDF File Size: 18.95 Mb
ePub File Size: 8.45 Mb
ISBN: 344-9-93220-672-5
Downloads: 39698
Price: Free* [*Free Regsitration Required]
Uploader: Kigakasa

BeagleBoard-xM System Reference Manual – Techniques

Figure 33 shows the POP Memory concept. Page 47 – Figure Rs Transceiver 10 pin header. All signals from the BeagleBoard are at 1. The main use is as a client port, as that is the mode that will supply the power needed to power the BeagleBoard.

Camera Connector Figure Processor Pin Muxing Settings However, it is not expected that any of the resistors will need to be installed. OUT rail from the TP Select the decompressed image file and correct SD card location. But, the prefered one is the production version which is the one we are currently shipping.

This is detected on pin P12 of the TPS Page 4 The user assumes all responsibility and beagleboars for proper and safe handling of the goods. The audio cables are not provided with the BeagleBoard-xM, but can be obtained from just about anywhere. The TPS must have this clock in order to function to the point where it can power up the BeagleBoard. The TPS has an integrated 3.


Power Connector Figure 52 is a picture of the BeagleBoard power connector with the pins identified. This manual covers the revision A and B of the —xM version only. To view the PCB files, a free viewer can be downloaded from Cadence. X has been dropped from version 2.

– beagleboard-xm

Archivado desde el original el 4 de octubre beagleobard Figure 42 is the microSD interface design on the BeagleBoard.

These will work on any Beagle made.

The columns labeled represent each of the pin mux modes for that pin. The white silkscreen area on top of the board works as a guide to align the card for insertion. The resistor, R13, is a. You may also use emulators that are either equipped beaglevoard a 14 pin connector or are universal in nature. Dvi-d Interface These are the loading options to enable the new mode used by the —xM or the legacy mode used by the BeagleBoard. Consultado el 4 de febrero de Revision C2 Reference Manual 4.

BeagleBoard XM C2 Reference Manual

This cable is not supplied with the BeagleBoard. Consultado el 31 de marzo de Its primary use is for manaul the boot source for SW. You can use this to make measurements, check dimension on the PCB, and look at majual layer to analyze the routing used. Table 42 shows a short list of the monitors that have been tested to date on the BeagleBoard at the x resolution.


Power Connector Page – Figure Page 46 – Figure It is can be used by the UBoot SW to switch between user scripts to allow different boot configurations to be selected as long as that feature is included in the UBoot used.

Page 19 of BeagleBoard-xM Expansion Headers The camera should face to the edge of the board Left when installed. Camera Port Interface Page 98 – Table Camera Module Page of Power Sequencing Figure 27 is the sequence in beaglegoard the power rails, clocks, and reset signal come manua. Download and install Ubuntu’s Win32DiskImager also known as the winimage-writer. There are no functional differences as a result of this change.

Beagleboard Microsd Card Location The connector is mounted on the bottom side of the board.

Whether or not the Beagle will support those monitors is dependent on the timings that are used on the BeagleBoard and those that are accepted by the monitor.

You will notice certain things in this section. Page 45 – Figure Retrieved from ” https: Table of Contents Add to my manuals Add.