BONFIGLIOLI VECTRON MANUAL PDF

You are here: Home · User Manuals · Inverters and Energy Recovery · Operating instruction; ACU Operating Instructions Frequency Inverter V / V. The safety instructions and information on use in this documentation must be Please note, that Bonfiglioli Vectron does not take any responsibility for the. 02/ Operating Instructions Agile. 3 Please note, that Bonfiglioli Vectron does not take any responsibility for the compatibility of external products (e.g.

Author: Nimi Akizahn
Country: Czech Republic
Language: English (Spanish)
Genre: Science
Published (Last): 23 August 2013
Pages: 117
PDF File Size: 14.13 Mb
ePub File Size: 6.45 Mb
ISBN: 316-7-51771-236-7
Downloads: 60789
Price: Free* [*Free Regsitration Required]
Uploader: Shajinn

Attention must be paid to the fact that only one master for each SDO channel may exist in a system.

Show all Vectron syn10 s 05 Vectron syn10 s 01 af. The mains, direct voltage and motor sockets can have dangerous voltages even after disconnection of the frequency converter.

The mapping is not done via mapping parameters as with CANopen, but via the method of sources and links. After that proceed on the set characteristic.

Do not touch electronic components or contacts. The power filters are a component to improve EMC behavior in a machine installation.

Selecting The Destination Identifier assignment according to the Predefined Connection Set: Operational Environment The installation site of the inverter is very important. Before commissioning and the start of the intended operation, attach all the covers and check manuao sockets. The selection of functions depends on the parameterized configuration. A thermal sensor for the brake resistor protects the resistor from overheating.

  ANATOMIA HUMANA FERNANDO QUIROZ TOMO 1 PDF

In addition, the system bus master reports the warning Sysbus 0x bonfiglloli the parameter Warnings Bit For further information, refer to the chapter “Electrical Installation” of the frequency inverter operating instructions. The Identifier must be clear in the system bus network.

Active Series : Bonfiglioli

All the setting parameters for the configuration of the system bus are not directly accessible for the user. The other bus termination must be passive.

After receipt of the Start Remote Node command, the nodes change into the Operational state. Time Acceleration time 0.

Bonfiglioli Vectron Syn10 S115 01 Operating Instructions Manual

This manual also for: The following examples show the operation modes for an analog voltage signal. Selecting The Source Further Motor Parameters Typical Conductor Cross Sections For specific areas of application further provisions and guidelines must be complied with where applicable. This assignment can be altered by parameterization.

Vectron syn10 s 03 Vectron syn10 s 03 af Vectron syn10 s 07 af Vectron syn10 s 09 af Vectron syn10 t 05 af Vectron syn10 t 07 af: Bulk long distance conveying Overland conveyor. vectton

Set Points At Multi-functional Input For node recognition in a CAL or CANopen system, the slaves on the system bus generate a starting telegram boot-up report. No additional malfunction in operation or stop occurs within 10 minutes.

XA XB 5 Terminal 5: XPI files can be read in addition to the loaded parameter information of the frequency vectrno into the VPlus PC program. Food freezing process Spiral conveyors. Observe the climatic conditions according to standard EN and to the information on the label of the original packing.

  AFMAN 23-110 PDF

In-Line Geared units C Series For the frequency inverter, two server SDO channels have been implemented.

Bonfiglioli act 401 Manuals

Resetting of SysbusEmergency is done with the fault acknowledgment. The speed Y of the drive mechanism is controlled according to the analog control signal X. Depending manul the application boundaries, certain EMC levels must be achieved. Control Inputs And Outputs Assignment of the inputs: When momentary power loss is longer than 2 seconds the large of horse power, the longer of timethe inverter does not have enough storage power to control the circuit; Connection Of The Device For reasons of clarity, we have not been able to take all detailed information on all the types of the products and vedtron not every imaginable case of positioning, operation or maintenance into account.

Example of the adjustment of the analog input with a voltage signal: The SYNC telegram is generated by the system bus master and is a telegram without data. Operation mode 0 -Off 41 -Abs.