E5CN-R2MT-500 MANUAL PDF

manual, RUN/STOP, and alarms) and the PV or SV. E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers User’s Manual Basic Type E5CN-R2MT E5CN/E5AN/E5EN Digital Temperature Controllers User’s Manual Basic E5CN -R2MT AC or E5CN-R2MTD AC/DC24). E5CN/E5CN-U Temperature Controller User’s Manual (Cat. No. H). E5CN Temperature Controller Communications User’s Manual (Cat. E5CN-R2MT-

Author: Bajind Mogor
Country: Cambodia
Language: English (Spanish)
Genre: History
Published (Last): 2 January 2014
Pages: 188
PDF File Size: 6.13 Mb
ePub File Size: 20.10 Mb
ISBN: 562-8-69587-200-5
Downloads: 31913
Price: Free* [*Free Regsitration Required]
Uploader: Tojagore

If the OFF time of control output 1 is less than ms, SSR failure detection and the heater current will not be measured. Insert the Controller into the rear case until you hear a click.

Replace the case at the same time. Protect Level Press the Level Key e5cn-r2jt-500 at least 1 s. Do not block the ventilating holes. Use alcohol to clean the Temperature Controller. If an input error output is enabled, the al-1 operation indication on the front panel will not light and s. Consult with your OMRON representative at any time to confirm actual specifications of manuao product.

Tighten terminal screws to a torque of 0. Fire may occasionally occur if terminal screws become loose. Using any other sockets will adversely affect accuracy. When two or more Temperature Controllers are mounted horizontally close to each other or vertically next to one another, the internal temperature will increase due to heat radiated by the Temperature Controllers and the service life will decrease.

Use crimp terminals with the specified dimensions M3.

EUROTHERM ERO LFS Controller PID Heater Break Alarm Rs485 W/ Manual Hardware

Therefore, the service life can be extended by lowering the temperature of the Temperature Controller. These devices can cause radio disturbances which adversely affect the performance of the Controller. Press the Level Key less than 1 s. IEC Shaded settings are the default settings.

  GAR7 CHALLAN PDF

EUROTHERM ERO LFS Controller PID Heater Break Alarm Rs W/ Manual Hardware | eBay

Confirm system safety before switching the mode. This enables the new E5CN to handle application requiring even greater response speed and accuracy. HE In the interest of product improvement, specifications are subject to change without notice. Outputs will turn OFF depending on the mode when switching to the initial setting mode.

Due consideration must be given to this time when incorporating Temperature Controllers in a sequence circuit. Mount the Temperature Controller so that it is horizontally level. Set up the power supply so that the voltage will reach the rated voltage within 2 seconds after turning ON.

Do not use the Temperature Controller in the following locations.

OMRON E5CN Datasheet: Ordering Information

It cannot be removed with the E5CN-U. When extending or connecting the thermocouple lead wire, be sure to use compensating wires that match the thermocouple types. Tool insertion hole Flat-blade screwdriver Unit: Panel cutout, Internal panel dimensions for panel mounting, wiring screw sizes, wiring terminal arrangement, and parameter setting methods. To reduce the danger of fire or electric shock, do not internally connect the outputs of different class 2 circuits.

Starting in automatic mode Press the Level Key less than 1 s. Design the system e. Press on the hooks on the top and bottom of the rear case to be sure that the hooks are securely locked in place.

E5CN-Q2MT中文资料_图文_百度文库

Do not connect anything to unused terminals. Pt or JPt No models with analog inputs Improved models 7. Use this Adapter when the panel has been previously prepared for the E5B. When placing the Controller back in the case, make sure that electronic parts do not come in contact with e5cm-r2mt-500 case.

  DMITRY VOSTOKOV PDF

It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements.

The e5cn-r2m-500 operation will stop when switching from operation level to initial setting level. The exposed current-carrying part to be inserted into terminals must be 5 to 6 mm.

Do not 14 use. Doing so may occasionally result in minor electric shock. You must turn OFF the power supply. Locations subject vibration or strong shock 2. Manua reduce the danger e5cn-r2mr-500 electric shock or fire, use the Temperature Controller in an controlled environment relatively free from polluting materials.

Locations subject to dust or corrosive gas especially sulfide gas or ammonia gas. The Controller can be removed from the case only with the E5CN. Tighten the terminal screws using a torque between 0.

SSR failure detection alarm setting range 0. C sp-2 SP 2 0 a ol-h MV upper limit Back-connecting Socket Manuwl 27 dia. Take appropriate safety e5cn-r2mt500, such as installing a separate monitoring system, to ensure safe operation in the event of a malfunction of the Temperature Controller. To convert grams into ounces, multiply by 0. Three-phase Heater Burnout Detection With Models with Three-phase Heater Burnout and SSR Failure Detection, two current transformers can be connected to detect both heater burnout and SSR failure at the same time, reducing costs because a separate heater burnout alarm device is not required.

Option Unit can be mounted 4.