M93C56, M93C 16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit (8-bit or bit wide). MICROWIRE® Serial Access EEPROM. FEATURES SUMMARY. 93C46 Technical Data, x8(1k) Serial CMOS EEPROM Datasheet, buy 93C 93C46 Datasheet, 93C46 1k Serial EEPROM Datasheet, buy 93C

Author: Taujar Aradal
Country: Mexico
Language: English (Spanish)
Genre: Business
Published (Last): 12 May 2010
Pages: 239
PDF File Size: 15.49 Mb
ePub File Size: 16.39 Mb
ISBN: 690-8-44070-813-8
Downloads: 79946
Price: Free* [*Free Regsitration Required]
Uploader: Tojashicage

Input port and input output port declaration in top module 2.

Company certificates We will provide the most professional and most comprehensive services. Embedded Systems and Microcontrollers. If I have a 93c46 in a circuit how can be read the memory content without being altered. Dec 242: Eeprom Programmer Kit At24c Ic.

If the file has been modified from its original state, some details such as the timestamp may not fully reflect those of eelrom original file. I have the circuit board with a 93c46 eeprom which through an 8 pin connector is linked to the main board.

Any sugestion would be very helpful. Infineon accepts no liability for the content and materials on this site being accurate, complete or up- to-date or for the contents of external links.

Read EEPROM(93c46) with PIC & Simulation

The question here is as follows: Electronic Components eeprom 93c And i am planning to do that with Proteus. This applies to both the 93C46 and 93CS Equating complex number interms of eeprok other 6.

Tags for this Thread wiggler eeprom mprog. Mar 16, 2. The 93C46 is a memory element. Mar 16, 11 0. Atb-sshl-t M Eeprom Eeprom 93c As the pressure on engineers to make products smaller has grown, semiconductor manufacturers have introduced several new interfaces, usually aimed at lower a product’s size and cost Feb 24, 11, 2, There are lots of other distributors too, but Mouser and DigiKey are probably the easiest, since they give out a free catalog What this family code does This code was written to support the 93CS I’m still waiting for some more suggestions.


All postings and use of the content on this site are subject to the Usage Terms of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Usage Terms of this site. Do you think should be another approach?

In addition, WEN may have to have been called, check your data sheet or just do it to be on the safe side. They offer quite a few different types of serial eeproms, including of course the 93CS46 and 93C Mar eepprom, 3. They are usually specified to retain the data for 10 years and to endurewrite operations before failure. Mar 17, 6. Choosing IC with EN signal 2.

As mentioned above, four wires are actually required, and the 93CS46 has two additional lines that work together with a special write protection register. This 3-Wire interface chip actually has 6 wires. This disables write operations. The 9c346 can be adapted to work with these larger chips There is no way to undo this operation No, create an account now.


Feel free to choose one of the free licenses stated below. Also at using an Arduino circuit as well might be a possibility to test but I’ll need more directions for that.

In addition, a considerable length of time milliseconds is required to perform a write operation. The problem is that the miniwiggler try connect to the TC but can’t! The routines available for your code are: It’s up to you. Disclaimer These 93C46 9c346 EEPROM devices are used in many deprom products where the data contained within the chip, though only bytes, is considered confidential and proprietary. Losses in inductor of a boost converter 9.

Reading the data of a 93C46 eeprom

Early versions of this code worked with the 93C56 and 93C57, which have more memory. I am looking for a link or a simple application to be used in reading the data of a eeprom type 93C46 circuit used for counting the number and duration of activations of a 12V DC power source.

ModelSim – How to force a struct type written in SystemVerilog? This routine just waits for it to finish before returning Whether near the image or in a separate image directory, it should be specified: