Download FLUKE PM PM PM PM 2X2MV,MHZ OSCILLOSOPE SM service manual & repair info for electronics experts. Re: Fluke PM manual needed (MHz scope) The service manual for Fluke / Philips PM PM PM PM can be found. PM ). Deflection Manual positioning: Horizontal, Vertical, Both . Web access: com.
|Published (Last):||24 May 2014|
|PDF File Size:||14.25 Mb|
|ePub File Size:||4.72 Mb|
|Price:||Free* [*Free Regsitration Required]|
ATCAL can supply several accurate voltages that are used for vertical calibrations. Properties expressed in numerical values without tolerances, ranges or limits stated, represent the characteristics of an average instrument. Governing Law These Conditions and any Conditions contained in the Notices to Purchasers, along with all associated transactions and all connected matters shall be governed and construed in accordance with English Law.
Type of instrument Required specification This delay is verified in the following test. As from the date and time the Buyer is declared, all risks in and relating to the Goods purchased, shall pass to the Buyer and the Buyer is strongly advised to effect insurance for these risks at once.
In the signal name list you find the itemnumber of the component that is source or destination.
After repair and maintenance in the primary circuit, safety inspection and tests, as mentioned in This diagram shows the Y-output amplifier. All channels and functions seems to operate just fine. Governing Law These Conditions and any Conditions contained in the Notices to Purchasers, along with all associated transactions and all connected matters shall be governed and construed in accordance with English Law Page This delay is verified in the following test. On the power supply unit there are many parts that carry dangerous high voltages.
The mains fuse has really exploded. Ask seller a question. However, many of the standard electronic components can be ppm3082 from other local suppliers.
Fluke PM3084 Analog Oscilloscope
This gives a time-linear voltage across the capacitor; the so- called sawtooth or sweep signal. Page DC coupled mode. VAR4 is varied between min and max in various sensitivity positions. Mains rectifier ok, switch ok, snubber, line filters all ok. Control of the illumination amplifier V takes place by means of the signal DAC2, level about 1.
On the XYZ unit there are parts that carry high voltages. A brief examination of the primary side of the smps reveals no shorts. Like if he forgot to use the isolation transformer. Bidding for any lot shall be deemed to be an acceptance of these conditions and any conditions in the Notices to Purchasers.
The highest bid at the close of bidding subject to approval by the Auctioneers and Vendor also marks a conclusion of a contract of sale between the Vendor and the Buyer.
Come back when bidding opens to start bidding. Differences between these models are the vertical bandwidth, the features of the vertical channels 3 and 4 and the presence of switcheable 50Q input impedance.
If any written notice manuql delivered by hand, it shall be treated as having been received at that time. Your registration has been successful. On 14 Juni, For this reason the illumination voltage can be varied between about 2 and 28 V.
Anyway, it appears that I’ve got another nice looking four channel oscilloscope on my bench! Apparatus should be properly grounded through the protective ground conductor of the power cord. This procedure is intended to: You are the current highest bidder!
Therefore, it is recommended to wait at least five minutes after having disconnected the unit from the mains, before removing the unit. Venue Address Lefevre Way. Any concluded contract flu,e sale is made directly between the Vendor and the Buyer. The output signals are measured on the X-deflection plates of the CRT. The horizontal MTB deflection coefficients can be varied in steps such as done in 6.
These names make it easier to trace a signal going from one circuit diagram to another. Biasing current for these outputs is provided via V, V and R If working on the manhal under live condition cannot be avoided, it must be done by a qualified technician who is aware of the dangers involved.
The HF section for frequencies above 5 kHz.
PM User Manual – PM Oscilloscope from Fluke
Main Time Base Description. The output signal is voltage and is applied to the vertical deflection plates of the CRT.
Table Of Contents 6. When instrument is switched off or during mains failure. Your question has been sent to the auctioneer. Third Party Rights Save as expressly provided in these conditions, no term of these conditions shall be enforceable under The Contracts Rights of Third Parties Act by a third party. To be sure to win, come back on 15 Sep