Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.
|Published (Last):||21 January 2006|
|PDF File Size:||7.35 Mb|
|ePub File Size:||9.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
The operation speed can be set in 2 ranges of slow speed mwnual and high speed operated as a safety function by setting 2 switches.
Page 39 Helicopter basic setting procedure etc.
Please reference the following link Futaba has provided to re-submit your repair or to obtain product support. Curve setting examples actually creating a curve, enter the data specified The curves shown below were created by using per the futabq or the reference value.
See the instructions for each specialized function for further For CCPM helicopters, be sure to read the details. The system servo throws, generates differential throws, and uses the programmed speed delay to slow down servo will correct improper linkage settings.
Use only the Futaba lithium ion transmitter charger included with this set for, or other chargers approved by Futaba to charge the Li-Ion batteries in the 1 Z transmitter.
Futaba 12Z User Manual | Page /
When to PPM mode. By pressing ‘print’ button you will print only current page. Page 44 Servo connection by model type The T12Z transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. Hold the lever head “B” and turn the lever head “A” Manhal once operating the cursor lever to button.
FUTABA 12Z Series Manuals
The Servo Speed setting is used to set the servo delay The End Point function adjusts the left and right for each channel, from channel l to channel BUTTERFLY This function allows powerful ,anual operation by simultaneously raising the left and right ailerons and lowering the flaps camber flap, position to be changed, the reference point is This setting will allow the ailerons to be raised while the flaps are simultaneously lowered.
It adjusts the a perpendicular position at neutral, the futana swash-plate to operate correctly for each control compensation functions in this menu may not This allows use for switching convenient. Fuselage linkage Connect the throttle rudder, aileron, elevator, pitch, and other servos in accordance with the kit instruction manual. The channel assignment initial setting for each model type is shown below.
THROTTLE MIX This function corrects slowing of engine the mixing item corresponding to the mixing that speed caused by swash plate operation at aileron needs correction and push the enter button to call or elevator operation.
FUTABA 12Z SERIES INSTRUCTION MANUAL Pdf Download.
This function is designed to allow you to reset selected portions or all of the settings saved in Resets all the functions in the Model Menu the active model memory. Throttle cut setting servos can be adjusted as needed. Page 89 Setting method turn the data input dial to the left and push the enter The rate and curve of each servo can be set by calling each screen.
Safety precautions when you install receiver and servos Warning Wood screw 2. Futba time you press a trim button, the trim position moves one step. Page 21 Safety precautions when you install receiver and servos Warning Wood screw 2.
In order for you to make the best use of your system and to fly safely, please read 1z2 manual carefully. Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below. Page Operations related to servo speed Servo speed setting 1 Servo speed setting 2 The servo speed at each function operation including flight condition switching can be The operation start point at operation IN adjusted. Switch selection method lever, or VR are used as a switch setting method is common to all functions.
Function, Functions of linkage menu, Function change – Futaba 12Z User Manual
The setting screen appears. Up to 3 rates can be set for each condition. Page 57 SUB-TRIM The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. Trim mix function call can be linked to a stick, For a description of the setting method, see For PCM mode, you can set eight linear channels and one digital channel. Operation modes Symmetrical box mode The operation modes when stick, trim lever, or but left and right up and down operation is knob was selected are described below.
Never hold the antenna alone.